Generic Uncle Henry questions

A place to ask or answer knife related questions.
Post Reply
Centerfinger
Posts: 20
Joined: Wed Mar 19, 2008 10:45 pm
Location: Scottsdale, AZ
Contact:

Generic Uncle Henry questions

Post by Centerfinger »

I got my first Schrade product (gently used) today in the mail and I must admit that its a well built quality slippie. I got an Uncle Henry 897UH and its impressive to say the least. I didn't think I was going to like the fake stag handles, but they are actually quite impressive.

I looked through the list of Uncle Henry's in the articles & research area and noticed that some of the UH's are listed having Schrade + steel, but the pattern I got does not have the note and has the stainless blades.

My questions are: Do most of the UH's come in both carbon and stainless steels? Are there value differences from a collectors stand point between the steels? I know there are lots of Schrade horders here, but for a newbie collector would the UH's be a good brand to start with? The price points are a little easier on my pocket book than say Case or Queen.

Thanks for any assistance.
My un-updated blog - http://www.centerfinger.com
User avatar
El Lobo
Gold Tier
Gold Tier
Posts: 3036
Joined: Tue Dec 14, 2004 4:47 pm
Location: Arizona, right here in the U.S. of A.

Re: Generic Uncle Henry questions

Post by El Lobo »

The Uncle Henry line was Schrade's UPSCALE (read...faux stag Delrin, instead of sawcut Delrin) product. The line therefore was predominently offered in stainless blades, thought to be an upgrade by Schrade management. There were some early, early carbon blades, on a few fixed blades, I believe...but, I've not seen an Uncle Henry folder with carbon blades.
Even some of the traditionally carbon bladed Old Timers began showing up with one or more stainless blades, sometimes not marked with a +, near the last few years of production.

Others (Dale, Kaleb, Larry...) may have more to add.

Rob, as a newcomer to Schrades, may I suggest a trip to this great website.....

http://www.collectors-of-schrades-r.us/


Bill
Please visit the Member Stores here at AAPK, including my store.....GET AN EDGE!
http://www.allaboutpocketknives.com/getanedge
Centerfinger
Posts: 20
Joined: Wed Mar 19, 2008 10:45 pm
Location: Scottsdale, AZ
Contact:

Re: Generic Uncle Henry questions

Post by Centerfinger »

Thanks Bill, I actually ran across that site earlier today whilst searching for info. Thanks for the info on the stainless blades, that is helpful.
My un-updated blog - http://www.centerfinger.com
keithlong
Posts: 654
Joined: Sun Jan 06, 2008 6:16 pm

Re: Generic Uncle Henry questions

Post by keithlong »

Hi
I have an UH 885 stockman that i use every day and whittle with it alot. Holds an adge great. Love the stainless blades, hard to sharpen without a diamond stone though. I have had mine for 4 years now and never leave home witout it.
KeithLLong

It does not cost any more to carry a sharp knife than it does to carry a dull knife
User avatar
jonet143
Gold Tier
Gold Tier
Posts: 6922
Joined: Fri Jun 23, 2006 3:33 am
Location: w'ford-tejas

Re: Generic Uncle Henry questions

Post by jonet143 »

that schrade + works, eh, keith? i love a knife ya can use.
johnnie f 1949

on the cutting edge is sometimes not the place to be.
please support our troops - past and present
if not a member...join the NKCA! they're on our side.
Post Reply

Return to “Knife Related Q&A”