need help identifying old case knife

A place to ask or answer knife related questions.
Post Reply
dhens
Posts: 4
Joined: Sat Oct 28, 2017 2:00 am

need help identifying old case knife

Post by dhens »

The Tang on the knife says it's WR case and Sons Bradford PA
Attachments
20171027_212704.jpg
User avatar
gsmith7158
Gold Tier
Gold Tier
Posts: 8617
Joined: Fri Dec 25, 2015 7:25 pm
Location: Canton, Ga. 100% of the time
Contact:

Re: need help identifying old case knife

Post by gsmith7158 »

Could be real. The stamp is difficult to see but looks ok. Most likely rehandled.
------------------

Greg

IF YOU AIN'T BUYING OR LOOKING AT A KNIFE THEN YOU AIN'T LIVING.
Always looking to buy good quality Empire knives.

PROUD MEMBER AAPK, NRA.
dhens
Posts: 4
Joined: Sat Oct 28, 2017 2:00 am

Re: need help identifying old case knife

Post by dhens »

Better picture of the tang
Attachments
15092213290811734823925.jpg
User avatar
danno50
Gold Tier
Gold Tier
Posts: 3918
Joined: Mon Jan 12, 2009 12:05 am
Location: Saskatchewan, Canada

Re: need help identifying old case knife

Post by danno50 »

Since there have been 24 views and no other comments, I will venture forth. This was a tang stamp used from 1904 to 1914 (from Sargent's 7th). Looked through all the W.R. Case & Sons knives in Sargent's 7th and did not see a lot of smooth bone handles. The third handle pin (above the centre pin) looks suspicious to me. Most Case jacks have only the two handle pins and the centre pin? Looking through Sargent's, the only patterns with 3 handle pins are the 6216 and the 12130. How long is your knife closed?
Dan
Dan
dhens
Posts: 4
Joined: Sat Oct 28, 2017 2:00 am

Re: need help identifying old case knife

Post by dhens »

3.750 inches long
User avatar
danno50
Gold Tier
Gold Tier
Posts: 3918
Joined: Mon Jan 12, 2009 12:05 am
Location: Saskatchewan, Canada

Re: need help identifying old case knife

Post by danno50 »

3 3/4" is the correct length for a 6231, which your knife looks like (other than being a single blade). Actually, the photos of the 6231's of this vintage in Sargents, appear to have 3 handle pins. The only book I have with a complete list of W.R. Case & Sons patterns is the 1976 Price Guide to Romance of Knife Collecting by Mrs. Dewey Ferguson. It does not list a one bladed 31 pattern? I am now way over my head on this and can only speculate that Greg is correct, that the knife was rehandled at some time. Could have been a 6231, which had the pen blade removed when it was rehandled? However, looks to me like if this was the case that it was done a long time ago?
I have already speculated far beyond my knowledge. Whatever it is, it is a good looking old knife! ::tu:: ::tu::
Dan
Dan
User avatar
orvet
Gold Tier
Gold Tier
Posts: 19906
Joined: Tue May 16, 2006 6:23 am
Location: Willamette Valley, Oregon

Re: need help identifying old case knife

Post by orvet »

I'm the first to tell you I'm no expert on Case, I have worked on a lot of old knives. That handle may not be smooth bone, it may be stag but it has been worn smooth. It looks pretty porous for bone.
Again I don't know a lot about Case specifically, but on wider frames it was fairly common to use a handle pain across from the rocker pin, especially if it has been rehandled and the first handle was a synthetic of some sort like celluloid.
Dale
AAPK Administrator

Please visit my AAPK store: www.allaboutpocketknives.com/orvet

Job 13:15

"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
dhens
Posts: 4
Joined: Sat Oct 28, 2017 2:00 am

Re: need help identifying old case knife

Post by dhens »

Back spring view
Attachments
1509238157556571502239.jpg
Post Reply

Return to “Knife Related Q&A”