unknown manufacturer?
-
srooka
- Posts: 3
- Joined: Thu Dec 08, 2005 3:04 am
unknown manufacturer?
i was wondering if anyone could help with any information about a knife i bought at a local sale. its a 2 blade folder about 2 1/2 inches closed, the blade has rex cut corp. germany on the other side joy 202 stainless. i have searched the web wit no results. any help would be great.
- Attachments
-
- DSCF0003.JPG (66.9 KiB) Viewed 2228 times
-
- DSCF0012.JPG (86.18 KiB) Viewed 2228 times
-
- DSCF0016.JPG (132.14 KiB) Viewed 2228 times
-
El Lobo
- Gold Tier
- Posts: 3036
- Joined: Tue Dec 14, 2004 4:47 pm
- Location: Arizona, right here in the U.S. of A.
If you don't have a picture of the stamp to show us it is mostly guessing.
Goins' Encyclopedia lists several REX stampings.
EDITED: OK then...now we'll see what we can find. Give us a day or so.
Tell us what the exact stamp reads...Number of lines...CAPITAL letters vs lower case...etc.
JUST GUESSING...Sounds like a common German import from the 60s-70s.
Bill
Goins' Encyclopedia lists several REX stampings.
EDITED: OK then...now we'll see what we can find. Give us a day or so.
Tell us what the exact stamp reads...Number of lines...CAPITAL letters vs lower case...etc.
JUST GUESSING...Sounds like a common German import from the 60s-70s.
Bill
-
El Lobo
- Gold Tier
- Posts: 3036
- Joined: Tue Dec 14, 2004 4:47 pm
- Location: Arizona, right here in the U.S. of A.
Maybe someone else will have more to add, but here is what I could find.
I have never personally seen this stamping...the only reference I was able to find was in Goins' Encyclopedia of Cutlery Markings. He states that the Rex Cutlery Corporation was located at 24 Cordier St., Irvington, New Jersey. A Kurt Schlesinger was the president, and they dealt mainly in scissors, around 1945-46.
MY CONJECTURE would be...
Since the knife is marked Germany (a U.S. law for imports after 1891), Rex was probably one of many importers of German cutlery, rather than a maker of knives.
No joy, as it were, on the JOY marking...maybe an inhouse brand used by Rex Cutlery??? Is that marking on the smaller pen blade different??
Sorry I wasn't able to help more than a tiny bit. If you are still curious, you might post these pictures at Bernard Levine's forum here...
http://www.bladeforums.com/forums/forum ... .php?f=691
It is the busier of his two forums, and since he didn't list the marking in his thorough book, he might take a particular interest in your knife.
For best results, include the length of the knife when closed, try to resize your pictures down just a bit. He can be a, well, crabby sometimes...but he is probably the best at knife identification. He doesn't give free apraisals, as that is his line of work. However he may tell you if it is worth your money to have one done.
There are also some other knowledgeable people both here, and over at bladeforums who might have more information for you.
Good Luck.
Bill
I have never personally seen this stamping...the only reference I was able to find was in Goins' Encyclopedia of Cutlery Markings. He states that the Rex Cutlery Corporation was located at 24 Cordier St., Irvington, New Jersey. A Kurt Schlesinger was the president, and they dealt mainly in scissors, around 1945-46.
MY CONJECTURE would be...
Since the knife is marked Germany (a U.S. law for imports after 1891), Rex was probably one of many importers of German cutlery, rather than a maker of knives.
No joy, as it were, on the JOY marking...maybe an inhouse brand used by Rex Cutlery??? Is that marking on the smaller pen blade different??
Sorry I wasn't able to help more than a tiny bit. If you are still curious, you might post these pictures at Bernard Levine's forum here...
http://www.bladeforums.com/forums/forum ... .php?f=691
It is the busier of his two forums, and since he didn't list the marking in his thorough book, he might take a particular interest in your knife.
For best results, include the length of the knife when closed, try to resize your pictures down just a bit. He can be a, well, crabby sometimes...but he is probably the best at knife identification. He doesn't give free apraisals, as that is his line of work. However he may tell you if it is worth your money to have one done.
There are also some other knowledgeable people both here, and over at bladeforums who might have more information for you.
Good Luck.
Bill