Do you see the difference ??????

big monk · Post by **big monk** » Tue May 03, 2011 4:21 pm

Do you see the difference in the two knives ??????? Neither knife is mine ( stock photos )_____Monk

tjmurphy · Post by **tjmurphy** » Tue May 03, 2011 4:23 pm

One has slanted bolsters.

big monk · Post by **big monk** » Tue May 03, 2011 4:42 pm

Ding-Dong-Ding-Dong !!!!!!!!!!!!!!!!!!!!!!!!!! TJ,you win the prize !!!!!!!!!!!!!!!!!!!!!!!!!!! I was just browsing,and happen to notice this ????? Doc's has three of these and they,are the only ones,that I've seen listed like this??? maybe an oversight,on the makers part ?????

tjmurphy · Post by **tjmurphy** » Tue May 03, 2011 4:54 pm

Tidioute bolsters on a Northfield knife. Better buy that one.

big monk · Post by **big monk** » Tue May 03, 2011 5:01 pm

tjmurphy wrote:Tidioute bolsters on a Northfield knife. Better buy that one.

Not quite ,TJ-----they did ring groove em'

________just fergot to slant em'

tjmurphy · Post by **tjmurphy** » Tue May 03, 2011 5:11 pm

Oops. Yep yer right. Missed that

mito0 · Post by **mito0** » Tue May 03, 2011 6:39 pm

from what i understand, the straight-bolstered version was a test run - very few were made.

WelderBob · Post by **WelderBob** » Tue May 03, 2011 8:26 pm

Short run on those Monk...not sure how many and I don't think they are numbered...should have one by the end of the week....

just in case · Post by **just in case** » Tue May 03, 2011 9:26 pm

I got one coming too ! And I went ahead and got that other knife that was in my shopping cart ... WHO PUT THAT THERE ??? ...Oh Boy....

Earl · Post by **Earl** » Tue May 03, 2011 10:40 pm

Man you fellas are a baaaad influence,just when I think I'm good for awhile

WelderBob · Post by **WelderBob** » Tue May 03, 2011 11:49 pm

Hey Earl...always glad to help a fellow out....

I think we can blame this one on Monk....

singin46 · Post by **singin46** » Wed May 04, 2011 1:44 am

Slantedor straight but fluted and pinched and I'm always in for that!

big monk · Post by **big monk** » Wed May 04, 2011 3:06 am

WelderBob wrote: I think we can blame this one on Monk....

who me??????????????

----just trying to help you guys out

Earl · Post by **Earl** » Wed May 04, 2011 3:16 am

Peer pressure......lol

Perry you been pick'n up any GEC's lately?

On Edge · Post by **On Edge** » Wed May 04, 2011 4:48 am

I did it! … I resisted! ... I did not run out and buy the rare and coveted straight-bolstered Calf Roper … !

… but then I picked up another 62 whittler and a half congress …

Can I blame them on Monk, too?

just in case · Post by **just in case** » Wed May 04, 2011 5:36 am

Yelp ! Him and BOB did it !

WelderBob · Post by **WelderBob** » Wed May 04, 2011 1:39 pm

Well fellow's you know Monk and I are alway's happy to point you in the right direction...

BTW....you guy's have good taste's in knives...

WelderBob · Post by **WelderBob** » Fri May 06, 2011 11:53 pm

Well other than the bolsters and the etch (I wish they would quit that) they are the same.

I'd really like to see a punch on this pattern...

All About Pocket Knives

Do you see the difference ??????

Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????

Re: Do you see the difference ??????