Craftsman Knives

[gsmith7158]

WOW... that is a sure 'nuff beauty Greg!

Thanks Mike!

[kootenay joe]

Here's an old Craftsman Sta-Sharp 9414 that I ran across inthe pile this morning.

Greg, i have the 'same' knife except no shield. Mine is marked "Craftsman/Sta-Sharp 9474". Are you sure yours is "9414" ?
kj

[gsmith7158]

Well my failing eye site has gotten me again Roland. You are correct. It says 9474. The top of that 7 was hiding just above the grind line.

[gsmith7158]

Here's a pretty decent stockman. No pattern number on this that I can see.

[kootenay joe]

Well my failing eye site has gotten me again Roland. You are correct. It says 9474. The top of that 7 was hiding just above the grind line.

Our 9474 knives are from different years as yours has a shield and mine does not. With many of the Craftsman knives a minor change like this would be given a separate new pattern number. It adds a level of 'confusion' when collecting Craftsman knives.
kj

[gsmith7158]

Well my failing eye site has gotten me again Roland. You are correct. It says 9474. The top of that 7 was hiding just above the grind line.

Our 9474 knives are from different years as yours has a shield and mine does not. With many of the Craftsman knives a minor change like this would be given a separate new pattern number. It adds a level of 'confusion' when collecting Craftsman knives.
kj

Yes I believe I have run up on that before with one of my whittlers. I'll have to see if I can round that one up.

[Ripster]

Well my failing eye site has gotten me again Roland. You are correct. It says 9474. The top of that 7 was hiding just above the grind line.

Our 9474 knives are from different years as yours has a shield and mine does not. With many of the Craftsman knives a minor change like this would be given a separate new pattern number. It adds a level of 'confusion' when collecting Craftsman knives.
kj

Yes I believe I have run up on that before with one of my whittlers. I'll have to see if I can round that one up.

Gentlemen you are showing some mighty fine Craftsman knives . They are sure nice on the eyes and gets the blood flowing.
And the little bits of info are always a plus and thanks for sharing that. Had wondered about the pattern number and some years they are different like the shield no shield thing.

[Meridian_Mike]

Here's a pretty decent stockman. No pattern number on this that I can see.

That is a BEAUTIFUL stockman Greg!

I looked in my file and I don't have any like that........ except for my Old Craftys and I know they would have a different number.

[gsmith7158]

Here's a pretty decent stockman. No pattern number on this that I can see.

That is a BEAUTIFUL stockman Greg!

I looked in my file and I don't have any like that........ except for my Old Craftys and I know they would have a different number.

Mike I've been rooting around in my pile this morning and found this short line 67. Looks like a dead ringer for that Craftsman stockman..

[Meridian_Mike]

Mike I've been rooting around in my pile this morning and found this short line 67. Looks like a dead ringer for that Craftsman stockman..

Sure does....

SO, was your Craftsman from the time before Sears was putting model numbers on their knives?

[gsmith7158]

Mike I've been rooting around in my pile this morning and found this short line 67. Looks like a dead ringer for that Craftsman stockman..

Sure does....

SO, was your Craftsman from the time before Sears was putting model numbers on their knives?

Mike I'm guess is that it probably had an etch at one time with the pattern number but that has long since vanished. Roland is very knowledgeable on Craftsman Knives. He may know the number for the Camillus 67 clones.

[kootenay joe]

Mike I've been rooting around in my pile this morning and found this short line 67. Looks like a dead ringer for that Craftsman stockman..

Sure does....

SO, was your Craftsman from the time before Sears was putting model numbers on their knives?

Mike I'm guess is that it probably had an etch at one time with the pattern number but that has long since vanished. Roland is very knowledgeable on Craftsman Knives. He may know the number for the Camillus 67 clones.

I don't know the Craftsman numbers for the Stockman patterns. But i do know that the Craftsman Sta-Sharp knives from 1930's came with an etch on the master blade.
Comparing the 2 Stockman knives above, the Craftsman Spey blade seems to have a deeper choil than the Spey on the Camillus 67. Maybe this varies with the guy who ground the blades ?
kj

[Ripster]

Here’s a 9528 with nice etch and solid bones . It’s about 3 and a 1/4 inches long . No cracks or missing bone . The blades have a bit of spotting going on so cleaned it up ,oiled it up and it’ll find a place with the others .

[doglegg]

[royal0014]

Knice addition to the pile JP

[Ripster]

Thanks Floyd and Chris
Have yourselves a great weekend .

[Meridian_Mike]

WOW....those bone Crafts MEN are killers!!
BEAUTIFUL bones!!

[Papa Bones]

Here’s a 9528 with nice etch and solid bones . It’s about 3 and a 1/4 inches long . No cracks or missing bone . The blades have a bit of spotting going on so cleaned it up ,oiled it up and it’ll find a place with the others .

Dang JP....that is a nice one right there. Great find!!

[Ripster]

Thanks Mike and Smitty. Haven’t been over here in a few so getting caught up .
While here going to show a couple pics of a Sears and Roebuck 1902 and 1908 Catalog cuts from there Cutlery Section . Sears Tang stamps in one and Wilbert in the other . Does anyone have any Sta Sharp Catalog info ?

[doglegg]

Great post JP.

[Meridian_Mike]

WOW.... those are some GREAT catalog pics!
Thanks for posting them!!

[gsmith7158]

Here's a 9529 whittler marked Forged USA

[dlr110]

Very nice Greg!!!

[gsmith7158]

Very nice Greg!!!

Thanks David!

[Meridian_Mike]

WOW.... that knife is a real treasure Greg!