Toe nail

stockman · Post by **stockman** » Sun Jul 15, 2007 2:07 am

I have posted about this old HS&B toe nail before trying to get information on the maker, the age and any additional information you may have. Scott helped me out alot on some information about this knife. Can any of the old knife boys tell me what this bone looks like to them it could be NYKC, Ulster, Camillus, or Utica.

Thanks Stockman

Forensic Jim · Post by **Forensic Jim** » Sun Jul 15, 2007 4:17 pm

Stockman you should ask Roger 2050. I'm sure he can tell you everything you need to know about that knife.

ratlesnake75 · Post by **ratlesnake75** » Fri Nov 28, 2008 3:03 am

Hello Stockman, super nice elephant toe. I am almost positive that is called rogers bone, and maybe someone can seconded my opinion for you, and just maybe this can narrow down who made it for HS&B.---Thx Mark

stockman · Post by **stockman** » Fri Nov 28, 2008 3:15 am

ratlesnake75 wrote:Hello Stockman, super nice elephant toe. I am almost positive that is called rogers bone, and maybe someone can seconded my opinion for you, and just maybe this can narrow down who made it for HS&B.---Thx Mark

Hello ratlesnake, I also thought it was Rogers bone, do not know for sure who made the knife. You must have gone back along way to find this post. Thanks for your help.

Stockman

ratlesnake75 · Post by **ratlesnake75** » Fri Nov 28, 2008 7:06 am

Hello Stockman, I do not know for sure. It would be difficult and just a guess cause the rogers bone company supplied there bone to most all other company's back then. Check out my posting under KUTMASTER SHOW ME YOURS in this category, I just posted a few pics of a jumbo jack that has that rogers bone. Thx Mark

ratlesnake75 · Post by **ratlesnake75** » Fri Nov 28, 2008 7:15 am

Hello Stockman, If you can start a NEW SUBJECT "WHAT CUTLERY MANUFACTURES MADE KNIVES FOR HS&B" then we can start eliminating the ones that did not use rogers bone or are seldom seen with rogers bone. And probably narrow it down to 1-3 manufactures who probably contracted that knife. One of the tail tail signs for me is to find out which company out of those that we find, MADE KNIVES WITH LONG PULLS ALL THE WAY TO THE TANG--LIKE YOURS(definetely early knife)--UTICA KUTMASTER DID NOT--AT LEAST I HAVE NEVER SEEN THEM TO THE TANG BY UTICA--what do you think there bud??--I have a good feeling after knowing the manufactures that made knives for hs&b we can get really close to nailing it. Thx Mark

Forensic Jim · Post by **Forensic Jim** » Fri Nov 28, 2008 9:25 am

I still have difficulty identifying Rogers bone. Sometimes it is obvious and with this knife, I would never have guessed it. Also, trying to understand what is referred to as "early Rogers bone", is another problem for me. Would this knife be considered "early Rogers bone" or just Rogers bone? That really is a fine looking vintage toe-nail though.

tmwsiy · Post by **tmwsiy** » Fri Nov 28, 2008 2:01 pm

looks like camillus to me

stockman · Post by **stockman** » Fri Nov 28, 2008 3:38 pm

tmwsiy wrote:looks like camillus to me

Could be tmwsit, I was always guessing Utica but Ratlesnake said the pull was not right for them. I do have a 4 line Camillus toe nail that is nothing like this knife.

Thanks Guys

muskrat man · Post by **muskrat man** » Fri Nov 28, 2008 4:06 pm

looks a lot like tidioute kabar to me?

stockman · Post by **stockman** » Fri Nov 28, 2008 5:48 pm

Thanks MM, I took a scam of my Camillus Toe Nail that I told you all earlier. It has steel Bolsters and is a 4 line. Poor picture couple clicks might help.

Stockman

tmwsiy · Post by **tmwsiy** » Fri Nov 28, 2008 8:06 pm

stockman wrote:
Could be tmwsit, I was always guessing Utica but Ratlesnake said the pull was not right for them. I do have a 4 line Camillus toe nail that is nothing like this knife.

Thanks Guys

my bad, I thought you were just asking about the bone in your OP... I have a camillus jack w/ bone thats very similar to that on your sunfish.

ratlesnake75 · Post by **ratlesnake75** » Sat Nov 29, 2008 4:57 am

Hello tmwsiy, You are both correct to me. Probably both of your knives have that rogers bone. Rogers bone was used on alot of knives by many cutlery company's. I have also posted pics of my utica kutmaster that has the rogers bone. Thx Mark

orvet · Post by **orvet** » Mon Dec 01, 2008 1:39 am

stockman wrote:Thanks MM, I took a scam of my Camillus Toe Nail that I told you all earlier. It has steel Bolsters and is a 4 line. Poor picture couple clicks might help.

Stockman

Nice knife!

If I might make a suggestion for your scanning.............I find I get better scans if I put a towel, or a piece of chamois over the knife before scanning. Even a manila envelop will help. The white top of the scanner has a strange effect on the pic if it is left uncovered.

Just a suggestion,
Dale

stockman · Post by **stockman** » Mon Dec 01, 2008 4:02 am

Thanks Dale, Also I have a problem with my picture size, sometimes they are nice and large and sometimes small. I don't know why. I have not changed anything. Usually if they are small I can click and make them bigger. I don't know computers and would throw this one away if not for AAPK.

Stockman

All About Pocket Knives

Toe nail

Toe nail

E Toe

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail

Re: Toe nail