Here it is all together. Minus the sharpening. I hand pein the pins. So they are a bit choppy looking. When peining it together I use a .007 shim between a blade and liner. When it is tight, I remove the shin and check for wobble. It usually takes several light taps to get it nice.
All blades have nice strong snap and no wobble.
Delrin rescale
-
Twhite
- Posts: 156
- Joined: Tue Nov 20, 2018 3:29 am
- Location: Burbank CA
Re: Delrin rescale
- Attachments
-
-
-
-
-
Twhite
- Posts: 156
- Joined: Tue Nov 20, 2018 3:29 am
- Location: Burbank CA
-
doglegg
- Gold Tier
- Posts: 23955
- Joined: Mon Sep 18, 2017 2:35 am
- Location: Grand Prairie, Texas
Re: Delrin rescale
Twhite, you should be proud. That looks very good. I'm proud for you. 
-
Twhite
- Posts: 156
- Joined: Tue Nov 20, 2018 3:29 am
- Location: Burbank CA
Re: Delrin rescale
Thank you. I am proud of the results.doglegg wrote:Twhite, you should be proud. That looks very good. I'm proud for you.
-
Steve Warden
- Posts: 6897
- Joined: Wed May 27, 2015 4:18 pm
- Location: Cherry Hill, NJ
Re: Delrin rescale
Looks great Tom!
Not much more satisfying than a job well done!!
Not much more satisfying than a job well done!!
Take care and God bless,
Steve
TSgt USAF, Retired
1980-2000
But any knife is better than no knife! ~ Mumbleypeg (aka Ken)
Steve
TSgt USAF, Retired
1980-2000
But any knife is better than no knife! ~ Mumbleypeg (aka Ken)
-
glennbad
- Gold Tier
- Posts: 8178
- Joined: Mon May 15, 2006 11:13 am
- Location: NH
Re: Delrin rescale
Looks factory from here!
-
orvet
- Gold Tier
- Posts: 19902
- Joined: Tue May 16, 2006 6:23 am
- Location: Willamette Valley, Oregon
Re: Delrin rescale
Great looking job!
I am wondering how you managed to smooth down the Delrin after you jigged it, did you sand it?
I am wondering how you managed to smooth down the Delrin after you jigged it, did you sand it?
Dale
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
-
Twhite
- Posts: 156
- Joined: Tue Nov 20, 2018 3:29 am
- Location: Burbank CA
Re: Delrin rescale
The Side I jigged was factory smooth and polished. After each jigging, I ised a nylon type brush on my Drexel slowest speed and no pressure on the jigging. This removed the hair and lightly buffed the surface.orvet wrote:Great looking job!
I am wondering how you managed to smooth down the Delrin after you jigged it, did you sand it?
After I was done I took it to a cloth polishing wheel on my mill. And very lightly buffed it to smooth things out. I could try polishing with Flitz by hand to get a better sheen. As this is just a beater practice knife I felt no need to do so..
ON a side note. The knife took a wicked edge. It seems to be a nice hard steel. I wish I knew who manifactured it.
I just bought my next project off of eBay a few minutes ago. This will be a serious refurb. I will be looking for direction on this project.
Tom
-
Meridian_Mike
- Posts: 5041
- Joined: Mon Apr 21, 2014 8:36 pm
- Location: Mississippi
Re: Delrin rescale
Nice job!
And thanks so much for taking us through your journey!
Mike
And thanks so much for taking us through your journey!
Mike
"Life is tough.... but it's tougher if you're stupid."....John Wayne
-
KleenCut61
- Posts: 810
- Joined: Thu Mar 23, 2017 2:17 am
- Location: Ulster Co, N.Y.
- Contact:
Re: Delrin rescale
Good Job! Great Tutorial On The Progress Also , 
K.C.
Great Tutorial On The Progress Also , K.C.-
Doc B
- Posts: 3700
- Joined: Fri Aug 10, 2018 10:57 pm
- Location: San Antonio
Re: Delrin rescale
Very nice! She has a new purpose now!
Heretical Refurb / Mods of cheap old folders, since late 2018