I generally have a knife or several close at hand at my 'puter desk.
I mess with them a LOT. Picked up my Primble Barlow and opened the blade to check sharpness.
It wasn't up to my standards. Tried ceramic, then coarse ceramic then blade steel and couldn't get it where I wanted it.
I don't have a mouse pad, but do have a large selection of sandpaper.
320 wet or dry was needed to get it where I wanted.
It's carbon steel. Must have a heck of a heat treat! Should STAY sharp for a good while!
Thanks for reading!
Tough Steel?
-
Just Plain Dave
- Bronze Tier
- Posts: 7724
- Joined: Sat Sep 05, 2009 3:54 am
- Location: Near East Texas (Cleveland area)
Tough Steel?
Looking for the magic penny!
-
TripleF
- Gold Tier
- Posts: 19621
- Joined: Mon Feb 14, 2011 3:42 pm
- Location: West Central FL
- Contact:
Re: Tough Steel?
Interesting....
thanks for sharing.
thanks for sharing.
SCOTT
Colonial Knife Company History ebook:
https://gumroad.com/l/ZLDb
Blog: https://scottrauberoutdoors.wordpress.c ... e-26-2026/
Colonial Knife Company History ebook:
https://gumroad.com/l/ZLDb
Blog: https://scottrauberoutdoors.wordpress.c ... e-26-2026/
-
philco
- Gold Tier
- Posts: 15552
- Joined: Sat Mar 22, 2008 9:32 pm
- Location: Kentucky (Wildcat Country)
Re: Tough Steel?
Dave,
I can recall way back when the local hardware stocked John Primble knives along with Schrade and Case. I was mostly into Case back then (70s) but I do remember a lot of the local "experts" raved about the edge holding ability of their Primble knife.
Phil
I can recall way back when the local hardware stocked John Primble knives along with Schrade and Case. I was mostly into Case back then (70s) but I do remember a lot of the local "experts" raved about the edge holding ability of their Primble knife.
Phil
Phil
AAPK Administrator
Jesus died for you. Are you living for Him?
"Buy More Ammo!"
Johnnie Fain 1949-2009
AAPK Administrator
Jesus died for you. Are you living for Him?
"Buy More Ammo!"
Johnnie Fain 1949-2009
-
Elvis
- Posts: 2185
- Joined: Tue Dec 22, 2009 2:22 pm
- Location: Cincinnati, Ohio USA
Re: Tough Steel?
Stainless is nice for the fancy collectibles that you know will never see any pocket time. When it comes to a working knife, the steel in those old John Primble's is about as good as it gets. I love my Case Knives and since I've been doing Kabar's folder repairs I've gained a lot of respect for their old carbon steel. Dad's old Primble Hawkbill that I treasure can still hold an edge with the best of them. With it being hard to sharpen, you can bet it will hold that edge for quite a while.
-
Owd Wullie
- Posts: 3627
- Joined: Sun Mar 01, 2009 4:31 am
- Location: Macomb, MO
Re: Tough Steel?
That old Buck 110 I have has one of the hardest damn blades of any knife I own. Buck didn't mess around back then. I still like carbon steel but that knife is an exception to my rule.Elvis wrote:Stainless is nice for the fancy collectibles that you know will never see any pocket time. When it comes to a working knife, the steel in those old John Primble's is about as good as it gets. I love my Case Knives and since I've been doing Kabar's folder repairs I've gained a lot of respect for their old carbon steel. Dad's old Primble Hawkbill that I treasure can still hold an edge with the best of them. With it being hard to sharpen, you can bet it will hold that edge for quite a while.
Member of The West Texas Chapter Of Gun Ownin', Pickup Truck Drivin', Jingoistic, Right Wing, History Changin', Huge Carbon Footprint Leavin' Conspirators.
-
trutemper
- Posts: 443
- Joined: Fri Jul 01, 2011 2:55 am
Re: Tough Steel?
The 70`s Primble steel was darn good but the older Primble India Steel Works knives were better to my way of thinkin.