How do I restore a gold knife?

Iellis16 · Post by **Iellis16** » Mon Jan 20, 2025 1:17 am

My son bought a SW Executive gold knife at a thrift store. It appears a bit dull, there is some rust but not too much, and we will need to tighten the bolt that holds the blade. I have two primary questions:

1. Where do I find the tool to tighten the bolt for the blade (see pic 1)

: Bolt tool?

2. How do I polish and restore the gold finish on the handle and blade? I am worried that using typical materials like wet sandpaper, solvent, and metal polish may remove the gold finish all together? Below is a pic of the knife we have (pic 2 and 3)and a pic of the knife as it should look (pic 4).

: Our knife 1

: Our knife 2

: How it should look

Railsplitter · Post by **Railsplitter** » Mon Jan 20, 2025 1:37 am

Good questions and I’m sorry that I can’t help.

I did notice that in the “How it should look” picture, the pivot has a Torx screw in the middle but yours doesn’t have one.

Is there a Torx screw on the other side under the pocket clip, by any chance?

Reverand · Post by **Reverand** » Mon Jan 20, 2025 2:55 am

I would polish it by hand using something like NeverDull, Flitz, or Mother's Mag polish.
As for the pivot screw, I have not seen one like that before.

Froe · Post by **Froe** » Mon Jan 20, 2025 3:43 pm

I don’t have any gold knives so I’m no expert. But if the gold finish is an anodized coating, metal polish can take it off. I saw that happen to a Kershaw Sapphire a guy was cleaning at a knife show. So you may want to test a little spot before applying to the entire knife.
Froe

SwedgeHead · Post by **SwedgeHead** » Tue Jan 21, 2025 4:45 pm

I beleive thats a gold tint Titanium coating, in case that helps.

hardman · Post by **hardman** » Wed Jan 22, 2025 3:54 am

I had a bad experience with a gold anodized coating on a blade. There were some corrosion 'blisters' that somehow formed between the gold anodized coating and the blade steel. The only way to remove the corrosion was to remove the gold coating.

1967redrider · Post by **1967redrider** » Wed Jan 22, 2025 3:27 pm

Does the nut on the clip side look the same? If not, remove the clip and tighten from that side. Would the #2 pencil treatment remove rust but not the titanium coating?

knife7knut · Post by **knife7knut** » Fri Jan 24, 2025 8:40 am

I would agree that the gold is a titanium coating. Supposed to be a satin finish; not polished. You would need a special face pin spanner to tighten the pivot nut, but you coukd improvise one by taking a pair of right angle needle nose pliers and grinding the tips to fit the holes.

Miller Bro's · Post by **Miller Bro's** » Fri Jan 24, 2025 9:46 am

Iellis16 wrote: ↑Mon Jan 20, 2025 1:17 am My son bought a.......

Another one and done

1967redrider · Post by **1967redrider** » Fri Jan 24, 2025 1:22 pm

Miller Bro's wrote: ↑Fri Jan 24, 2025 9:46 am
Iellis16 wrote: ↑Mon Jan 20, 2025 1:17 am My son bought a.......
Another one and done

Maybe he got better traction on BF?

Miller Bro's · Post by **Miller Bro's** » Sat Jan 25, 2025 8:16 am

RobesonsRme.com · Post by **RobesonsRme.com** » Fri Jan 31, 2025 2:42 am

Saw that coming

All About Pocket Knives

How do I restore a gold knife?

How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?

Re: How do I restore a gold knife?