Techman's first try at filework.
Posted: Wed Mar 19, 2008 11:03 pm
Please be kind, It was my very first try. After some more practice I am going to try a 23 single blade and put on some very nice colored Ironwood.
...CCBill...
All About Pocket Knives
All About Pocket Knives is a knife related resource center for buying, selling, researching, and discussing all things knives
http://www.allaboutpocketknives.com/knife_forum/
Techman's first try at filework.
http://www.allaboutpocketknives.com/knife_forum/viewtopic.php?t=8052
Page 1 of 1
Re: Techman's first try at filework.
Posted: Wed Mar 19, 2008 11:27 pm
Nicely done. Show us more...
...CCBill...
...CCBill...
Re: Techman's first try at filework.
Posted: Thu Mar 20, 2008 11:26 am
Looks like a good start to me! I've finally found a method that I'm happy with. I take good old blue tape and cover the flat and sides of the spring with it, making sure to get sharp edges on the corners. I layout a tiny grid (usually 1/8 lines down the length of the spring, then a centerline). That way I can make consistent cuts the without having the marks wear off on me halfway through (damn sharpies 
). An added benefit, is the filework stands out more while your working on it, since it's bright metal in a field of matte blue.
I haven't done any really ambitious file work yet (vine, etc) so you definitely started at the deep end
good work!
). An added benefit, is the filework stands out more while your working on it, since it's bright metal in a field of matte blue. I haven't done any really ambitious file work yet (vine, etc) so you definitely started at the deep end
good work!Re: Techman's first try at filework.
Posted: Sat Mar 22, 2008 9:07 am
Yes you will be doing more for sure. I think its nice to try things like this. You will have a higher level of love for knives when your done with this one try too. Time well spent and practice, practice, and practice...
Re: Techman's first try at filework.
Posted: Thu Mar 27, 2008 11:30 pm
Take 2, I only did the pattern I did not try to clean it up. I am almost ready I just wish I had a sharper angle file, knife type.
Blowing it up in the picture sure shows the flaws, it looks better in real life, smaller.
Blowing it up in the picture sure shows the flaws, it looks better in real life, smaller.
Re: Techman's first try at filework.
Posted: Fri Mar 28, 2008 2:39 am
LOOKEN good man....
Soon it will be time to go fishing will you be done with this by then..
...Just go fishing you need time out side too...
Soon it will be time to go fishing will you be done with this by then..
...Just go fishing you need time out side too... Re: Techman's first try at filework.
Posted: Fri Mar 28, 2008 12:22 pm
I will scan a knife or some filework & blow it up just to see flaws I miss with the naked eye.GECTECHMAN wrote: Blowing it up in the picture sure shows the flaws, it looks better in real life, smaller.
It is a good tool to help you prefect your work.
Dale
Re: Techman's first try at filework.
Posted: Sat Mar 29, 2008 3:01 am
Looks good to me TECHMAN Just keep working at it, and get you a small half round machinist's file, and grind the flat side smooth, be careful not to overheat the file though, if it gets to hot to hold with your bare hand, it's to hot, quench it in water, and start grinding again 
Just keep working at it, and get you a small half round machinist's file, and grind the flat side smooth, be careful not to overheat the file though, if it gets to hot to hold with your bare hand, it's to hot, quench it in water, and start grinding again Re: Techman's first try at filework.
Posted: Sun Mar 30, 2008 2:10 am
Ok I did it on the real spring, and I messed up so I threw it away. 
Fortunatly I had a spare junk one from my practice stash that I made work.
Only problem I broke a file I needed on the junk one to do the vine pattern.
So I come up with this pattern and I am not sure what to call it but I think it looks OK.
I know I messed up a little, hey its my first time.
Now I am excited to put it together, OOPS but this is not the word I used because I cracked the ARGENTINAIN LIGNUM VITAE handle.
So I take it apart and try some cocobolo, guess what, Those words again.
Now I grab my African Padauk and start over.
Well it worked out OK and here is a picture of it put together but I need to finish it still.
Fortunatly I had a spare junk one from my practice stash that I made work.
Only problem I broke a file I needed on the junk one to do the vine pattern.
So I come up with this pattern and I am not sure what to call it but I think it looks OK.
I know I messed up a little, hey its my first time.
Now I am excited to put it together, OOPS but this is not the word I used because I cracked the ARGENTINAIN LIGNUM VITAE handle.
So I take it apart and try some cocobolo, guess what, Those words again.
Now I grab my African Padauk and start over.
Well it worked out OK and here is a picture of it put together but I need to finish it still.