All About Pocket Knives

So this is my first post here. Also this is my first actual restoration. Anyways, I found this old fixed blade, looks like a skinner. It's well made with a nicely made hilt and pommel. So I knew it was a decent knife at one point. The problem being the blade is rusted and the makers mark is not legible. I tried many things to get the rust off unsuccessfully. Finally as a last resort I soaked the knife in vinegar overnight. Anyone who knows what that does to a carbon blade, knows what happened. After the soak I was able to scrub off the rust and was left with a Patina and some putting that was likely made from the rust and possibly some of it was from the "forced patina" from the vinegar. My question to you all is should I sand the blade down back to a "shiny" polish? Or should I leave the Patina along with the pitting? I know a Patina is loved by many and I admit it does look great with the knife. By the way, after I was able to get the rust off I can read the makers mark. The knife is an old Jean Case Cut Co with an Amber colored bakelite handle made in the 30s or maybe early 40s (the knife likely has some value to collectors). Cool knife. I like the look of the Patina but I'm not sure about the pitting
https://photos.app.goo.gl/xVE74nxBPUwtMmLE9

Just leave it, if worried about the pitting getting worse, a light coat of oil will stop that. Welcome to the forum.

Ya I think I've decided to leave it. If I grid it down, it's gonna be too thin. It looks good like this. Boy that edge needs some work. Gonna be huddled over a stone for a while I think haha

Meandmy1963 wrote: ↑Sat Oct 09, 2021 1:14 am Ya I think I've decided to leave it. If I grid it down, it's gonna be too thin. It looks good like this. Boy that edge needs some work. Gonna be huddled over a stone for a while I think haha

Just take your my friend, there is no rush.

cudgee wrote: ↑Sat Oct 09, 2021 1:45 am

Meandmy1963 wrote: ↑Sat Oct 09, 2021 1:14 am Ya I think I've decided to leave it. If I grid it down, it's gonna be too thin. It looks good like this. Boy that edge needs some work. Gonna be huddled over a stone for a while I think haha

Just take your my friend, there is no rush.

The best edges are usually a slow grind pun intended

Meandmy1963 wrote: ↑Sat Oct 09, 2021 1:50 am

cudgee wrote: ↑Sat Oct 09, 2021 1:45 am

Meandmy1963 wrote: ↑Sat Oct 09, 2021 1:14 am Ya I think I've decided to leave it. If I grid it down, it's gonna be too thin. It looks good like this. Boy that edge needs some work. Gonna be huddled over a stone for a while I think haha

Just take your my friend, there is no rush.

The best edges are usually a slow grind pun intended

Welcome to AAPK. I think you’ve made a wise choice to leave it as-is. I’m one who thinks an old used knife should look like, well, an old used knife. Too many, especially those new to the knife collecting hobby, think that making them shiny like new will make them more valuable. It won’t. Any experienced collector will know it’s not new.

Get the active rust off, and keep it off so it can’t do any more damage. Enjoy it. BTW most if not all the ones stamped Jean Case were made by Kinfolks. There are some fixed blade collectors here that can tell you more.

Ken

Looks like you did everything right so far. Pitting would bother
me too but there is nothing you can do. If you attempt to
grind away the pits the blades would be so thin you would
hate it. Just accept that the old knife has good character.
A patina will help prevent further damage.

Welcome to AAPK.

Bob

Welcome to the forum!!

Enjoy that knife!