Page 1 of 4
Electric Cut. Co.
Posted: Sat Jul 06, 2019 1:39 am
by FRJ
Here is a nice Electric Cut Co, Newark NJ. 2 15/16" closed. Half stops x 4.
I wonder if a previous owner tried to line these bolsters. That shoddy attempt belies an otherwise fine knife.
Also shown with an Electric from Walden, NY.
Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 2:04 am
by gsmith7158
Great find Joe! That's likely an early one judging by those stamps. Perhaps 1890-99.

Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 2:22 am
by FRJ
Thanks Greg and thanks for the information.

Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 2:13 pm
by LongBlade
Cool knife Joe

... who doesn’t like an old congress

... you think the bolsters were modified from the original knife? I am not at all familiar with Electric’s knives... is that bone jack in the last photo an Electric?
Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 2:39 pm
by FRJ
Thanks Lee.
The lining of the bolsters looks pretty rough. I hope it wasn't done by Electric Cutlery back in the day.
I think more care would have been taken then. Especially on a four blade pearl congress. It seems out of place but maybe they did it.
It looks like it was ground in with the corner of a carborundum stone. (slight exaggeration)
Yes, the bone jack is an Electric form Walden, NY.
Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 3:01 pm
by FRJ
Here is the Electric Cut. Co., Walden NY knife. 3 1/2"
Not exactly strong stamps.
Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 3:51 pm
by JohnR
Joe, nice early Congress, I have to agree with you, I think that lining was done by some previous owner and not factory, still a very nice hard to find early knife. Nice Jack also, have the same knife with a spear main and eo notch.
Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 3:58 pm
by danno50
Great pearl congress, Joe!

I agree with you and John about the ringed bolsters. The grooves are not parallel and they are deeper in the middle, ie don't follow the contours of the bolster. Also a nice jack.
Very nice condition jack, John!

Looks to have not been used much.
Re: Electric Cut. Co.
Posted: Sat Jul 06, 2019 4:25 pm
by FRJ
Thanks very much for the nice comments, John and Dan.
What a beautiful knife you have there, John. So full and clean. Very nice.
The Easy Open is a nice extra.
And nice stamps.
Re: Electric Cut. Co.
Posted: Sun Jul 07, 2019 1:55 pm
by RobesonsRme.com
Beautiful knives.
Even if done by a previous owner, the cuts on the bolsters are part of that knife's history, just as those extensive etches on that Angry Pruner in another thread.
Charlie
Re: Electric Cut. Co.
Posted: Mon Jul 08, 2019 6:14 pm
by wlf
Nice pattern Joe on rare stamp.
John that’s another of your beauties.
Re: Electric Cut. Co.
Posted: Mon Jul 08, 2019 6:30 pm
by FRJ
Thank you, Lyle.
Re: Electric Cut. Co.
Posted: Sat Jul 13, 2019 5:37 pm
by michaelspayth
Wish the stamp was a little be easier to read but can't argue with those beautiful green handles.
Re: Electric Cut. Co.
Posted: Sat Jul 13, 2019 10:40 pm
by FRJ
Nice honest old equal end there, michaelspayth.
Some body loved that thing. I do like those green covers too.
Thanks for showing it.

Re: Electric Cut. Co.
Posted: Wed Feb 19, 2020 5:26 pm
by peanut740
I have 3 Electric Cut Co.Newark,NJ I have picked up recently. 3 1/4" heavily built jack.Iron bolsters and liners.Stout snap on both blades.
Re: Electric Cut. Co.
Posted: Wed Feb 19, 2020 5:31 pm
by peanut740
Next is a 2 3/4" barehanded jack.NS bolster and brass liners.It also has a light Electric etch.
Re: Electric Cut. Co.
Posted: Wed Feb 19, 2020 5:37 pm
by peanut740
Lastly,a 3 1/4" pearl pen knife with a strong Electric etch.
Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 2:17 am
by Duffer
Here is an Electric Cut Co. Jack. Please notice that this one is Newark NJ marked. So it was made prior to 1910 probably around 1903 or so. It is a Jumbo Jack at 3 & 3/4 inches and has those highly desirable deep dark black Ebony handles found on early made antique folders. The blades are full with a lot of the original finish present. Snappy W & T and not a hint of wobble when blades fully deployed. Looks like much of the original factory cutting edge bevel still intact. Just a solid well preserved old Jack! Thanks for looking
Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 3:46 am
by gsmith7158
That's a great old jack Lloyd! Can't beat that old growth Ebony.

Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 6:19 am
by FRJ
I haven't looked at this thread in a while.
Roger and Lloyd have sure raised the bar here.
Thanks for showing these beautiful knives guys.
They really are special.
Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 8:31 am
by Duffer
Thanks Greg and Joe for your kind comments on my Electric CC Jack—much appreciated!!
Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 11:41 am
by BWT
That is a good looking ole jack Lloyd, my kinda knife

Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 12:19 pm
by galvanic1882
Sweet knives Lloyd and Roger

Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 1:18 pm
by JohnR
Great knives Roger and Lloyd, Lloyd really love that ebony Jack, old ebony is hard to beat.
Re: Electric Cut. Co.
Posted: Mon Apr 20, 2020 1:20 pm
by Waukonda
Duffer wrote: ↑Mon Apr 20, 2020 2:17 am
Here is an Electric Cut Co. Jack. Please notice that this one is Newark NJ marked. So it was made prior to 1910 probably around 1903 or so. It is a Jumbo Jack at 3 & 3/4 inches and has those highly desirable deep dark black Ebony handles found on early made antique folders. The blades are full with a lot of the original finish present. Snappy W & T and not a hint of wobble when blades fully deployed. Looks like much of the original factory cutting edge bevel still intact. Just a solid well preserved old Jack! Thanks for looking
Great old ebony, Lloyd
