Page 1 of 3
Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 2:19 am
by knifeaholic
From a large collection of miniature knives that I am selling...
This is a miniature 2" Easy Open jack. Celluloid handles, solid bolster.
Yes, it is marked...Guess the manufacturer.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 2:34 am
by buck16
Imperial?
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 2:38 am
by btrwtr
I'm thinking Colonial though a lot of these little gems are unmarked. If I get a second guess it would end in "ial" as well.
Wayne
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 2:51 am
by knifeaholic
Hmmm...Colonial would be a good guess but is not correct. Colonial did make a similar knife (see attached).
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 2:55 am
by knife7knut
Looks German;A.W.Wadsworth maybe?
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:03 am
by knives-are-quiet
Hammer Brand.........
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:07 am
by knifeaholic
It's American...not made by Imperial or Hammer Brand...
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:12 am
by knifeaholic
And remember I said that it SHOULD be easy...I did not say that it WOULD be easy.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:22 am
by knives-are-quiet
Then it must be either
SCHRADE or ROBESON ?????
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:29 am
by jerryd6818
French Ivory handles and the quality of work, I'm going with Queen.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:33 am
by daddynewton
Could it be Utica, I have a couple Utica minatures.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:41 am
by knifeaholic
knives-are-quiet wrote:Then it must be either
SCHRADE or ROBESON ?????
Have you ever seen a Schrade or Robeson miniature easy opener? I have not.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:42 am
by knifeaholic
daddynewton wrote:Could it be Utica, I have a couple Utica minatures.
Very good guess....but...no...
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 3:58 am
by knives-are-quiet
My last two guesses....
I doubt it is a CASE knife...
So maybe...........
PAL
or
REMINGTON????
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 4:41 am
by knife7knut
Looks like waterfall celluloid so maybe a Schrade?
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 5:20 am
by btrwtr
I am running out of guesses........UTICA?
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 5:26 am
by ScoutKnives
IKCO ? Camco ?
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 5:53 am
by knives-are-quiet
One More.....
"Ideal"
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 5:57 am
by btrwtr
Steve, I thought you said this would be easy. Ulster and I'm out of guesses.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 5:58 am
by Dinadan
Valley Forge
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 5:59 am
by jerryd6818
knives-are-quiet wrote:One More.....
"Ideal"
Ideal popped into my mind too, Jamie but I decided the knife was too well made for Ideal.
That's why I guessed Queen but apparently Queen was so far out of the running it wasn't even worth considering.
Edit: It appears to me to be a very well made knife. Makes me wonder if it really is a Case.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 6:05 am
by knifeaholic
Well, ask yourselves...which manufacturers made miniature (2 inch) easy open jacks like this one, based on your observation of actual examples?
And it is s solid bolster knife, not a shell handled knife.
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 6:12 am
by ScoutKnives
NCCO ?
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 7:25 am
by #goldpan
I have two minis with cell handles...
they are both unmarked though. My guess? Pal Blade Co.
Randy
Re: Ok another "Guess The manufacturer"...should be easy...
Posted: Fri Jun 26, 2015 7:29 am
by Mason
Ulster.