All About Pocket Knives

cody6268 wrote: ↑Tue Apr 14, 2020 10:16 pm

TPK wrote: ↑Sun Apr 12, 2020 3:41 pm

cody6268 wrote: ↑Sun Apr 12, 2020 3:25 pm Purple Spyderco Ladybug and Victorinox Cybertool 34

KIMG0200.JPG

Victorinox Cybertool 34 Been wanting a Tool with a bit holder. Nice!

I like bit drivers on multitools. Sometimes, the bits I mess with (T27, well nearly all Torx) aren't covered by the average multitool loadout, and I avoid Leatherman's bits and tools with bit drivers as they are two-dimensional and soft.


The CT line is more, or less, designed for work with computer; but it does have both Phillips #1 and #2. There is a second set of bits you can find (and I think it's easier in Europe) originally made for a version of the CT34 made for Beretta that is centered around handgun maintenance. Victorinox is still making them and selling them as replacements, as the XAVT has a second bit driver loaded with the Beretta bits. I have two computers that I plan to replace and upgrade the RAM on; one of them has to have the DVD drive taken out to access the sticks of RAM, and I know that's at least one of the Torx on the CT; and the case on my older PC uses Phillips (and the sticks of RAM I can actually see looking into the vent on the case; only the side of the case has to be taken off to access the RAM. But the CT41/CT L on the other hand, it's like the SwissChamp without all the silly stuff like the fish scaler and the added versatility of the CyberTool layer. If they weren't $150, I'd have had one by now. I think I paid around $30 for my CT34 used. The CT29 is like the Spartan, but adds the CT layer. Pretty slim for its functionality.


Gerber has a new tool that is SAK-sized, called the "Armbar Driver" with a 1/4 driver instead of the roughly 3/8 on the CT. Problem is that it has a known issue that has yet to be fixed--there is almsot no spring tension on the tools. I was actually gonna get one myself becaue of the 1/4 driver; but not until the problems with the design are remedied.

richard wrote: ↑Tue Apr 14, 2020 10:24 pm

Steve Warden wrote: ↑Tue Apr 14, 2020 9:57 pm

richard wrote: ↑Tue Apr 14, 2020 9:36 pm

i also have this 6232
same frame ? with 2 blades

Nice!!

If I may, the 6344 is 3 1/4" closed, the 6232 is 3 5/8" closed.

6 is code for bone
2 and 3 are code for number of blades
32 and 44 are frame numbers

If you knew this, forgive me. At the least maybe it will educate someone who may not know.

thank you steve , these both seem to be 3 5/8 closed . ?
so the red one is a 6332?

Steve Warden wrote: ↑Tue Apr 14, 2020 10:31 pm

richard wrote: ↑Tue Apr 14, 2020 10:24 pm

Steve Warden wrote: ↑Tue Apr 14, 2020 9:57 pm

Nice!!

If I may, the 6344 is 3 1/4" closed, the 6232 is 3 5/8" closed.

6 is code for bone
2 and 3 are code for number of blades
32 and 44 are frame numbers

If you knew this, forgive me. At the least maybe it will educate someone who may not know.

thank you steve , these both seem to be 3 5/8 closed . ?
so the red one is a 6332?

If it has 3 blades, then it seems like it. A 6232 has two blades.
Model number should be stamped on one of the blades.

This explains it in more detail ---> https://www.allaboutpocketknives.com/co ... ng-system/

Case XX 6383 wrote: ↑Tue Apr 14, 2020 3:16 pm good day for pics

J1890 wrote: ↑Wed Apr 15, 2020 6:30 pm One big, one small
8E7A2A45-E6B7-4884-8C36-D5B947AFB6ED.jpeg

DM11 wrote: ↑Wed Apr 15, 2020 10:16 am72 yesterday.

richard wrote: ↑Thu Apr 16, 2020 3:04 am pulled these old whittlers . out in the sunshine today. now to find something to whittle.

Quick Steel wrote: ↑Thu Apr 16, 2020 5:31 am richard, your knives are very nicely displayed. Good photo.

Case XX 6383 wrote: ↑Thu Apr 16, 2020 12:03 am I almost forgot to add my covid 19 mask that I am wearing to work tomorrow to see the faces

Montanaman wrote: ↑Thu Apr 16, 2020 5:52 pm Zulu spear made by Johnny Stout today, mosaic feather damascus blade forged by ABS Master Smith Jon Christensen, and feather damascus bolster forged by Mike Tyre, Sambar stag

aapk41620.jpg