All About Pocket Knives

Thanks Roger! I did note that reading Goins after posting my reply but thanks for the confirmation... I just can not find the patent using many different search options... actually if the patent was early in MB Cutlery history I am pretty sure that they just didn't use it on all knives - the question is why? Maybe due to the knife pattern not being amenable to the screws but even there I have seen smaller knifes from MB use and not use them on other patterns... maybe higher end knives used the screws

It is true that they did not use it on all of there knives, but really most from pre 1900 did have screws. It seems sometime around then they transitioned out of using screws. If you take a look at the rope knives and gravity knives, (Like Wiseguys) they made for the Spanish American War, it is around this time that you some are screw less. As time progressed and as they used up there stock (I imagine) it appears that the knives no longer feature screws. I would date any knives with screws likely to be pre-1910, unless they were contract knives, such as Maher & Grosh, who may have purchased a very large order. They, for example, continued to offer some screw handled Miller Bros knives into the 1920s, particularly there 4" Colorado Stock Knife) even though I don't think many other of their knives at that point were Miller Brothers made. These are just some thoughts.

Also, fantastic knife wiseguy. That is a really special one. Thanks for sharing it!

Thanks for the info Beechtree

Very informative and much appreciated.. I didn't realize it was more of an early development to use brass screws but had no rationale or reason as to why... I do know many patterns did use the brass screws and quite frankly I probably have more MB knives without the brass screws than with them... Also I thought I had read the rope knives were made under contract from Miller Bros to the US Govt during WWI and didn't remember them being made for the Spanish American War so thanks - - anyway not sure I ever saw a MB rope knife with anything other than brass screws but I maybe have just never seen one.... anyway I will store this info in my noggin for safe keeping (actually in my noggin may not be so safe

It likely was cheaper to pin than to screw on the handles.

Thats OK Lee, AAPK is here to keep the information safe from being lost from our leaky, sieve brains
I think you are absolutely right Roger, I would imagine it also took more time to instal then a pin.

Just dropped in for a minute, glad to see /read some thoughts on the screws I`m somewhat concerned that Dimitri hasn't chimed in given the topic heading , Maybe snowed in

I'm still kicking J!

Nice knives guys I like them all

Here's one. A little tired, but all there. 3 1/8".

Thats a good one Joe, I have a few. Heres one I have. You can barely see the etch and the pile side bone handle has been fixed where a peice broke off. I like it any way hope ya'll do too
Monte

Here's a Miller Bros. with a PhD.

A very strong little knife. 2 9/16".

Seems like you've been doing well lately Joe, that is a neat one. It has some pretty ivory handles.

Great full blades on that one montemojo, good score.

A couple of good ones Joe, thanks Beechtree

Thank you Beechtree and thank you montemojo.

Here is one of my best Miller's. Sadly it has been cleaned . I like it anyway and hope ya'll do too Thanks Monte

I like it! WOW! That's nice.

How long is it, Monty?

Joe it measures 4 inches. Heres another this one measured 3 and a half inches Monte

Very nice knives.

I Do Very nice MB Monte Lloyd

Thanks Joe, I have some more. I will post them in the future

Monte

Thank you Lloyd. I hope that more members will post theirs. I know ya'll got'em

Monte

Fantastic jumbo sleeveboard Monte! Thats a great knife.

Thanks Beechtree, the pictue was'nt the best. I wish it would have shown the double pull on the master blade

Monte

montemojo wrote:Joe it measures 4 inches. Heres another this one measured 3 and a half inches 20170305_204845.jpg
Monte

Can I see a clear picture of the tang stamps?

imitri, I am out pf town currently, as soon as I get home I will do my best. I should be home tomorrow evening. Thanks for looking. do you think there could be a problem with this one?


Monte