All About Pocket Knives

BBB!!! So Nice!!

Wonderful! - I'm speechless!

Here is an old Walden with most unusual aluminum bolsters nicely hand engraved.

One broken pen blade

here is an oldie -Its up for trade now on my knives for trade post

Gino, that's a Schrade-Walden, quite different from Walden Knife Company. The Schrade-Walden tang was started in 1947 (over 25 years after Walden Knife Co's demise) when the Baers combined Ulster Knife, Schrade, and Imperial Knife Cos....on the other hand, Walden Knife Co, a Schrade competitor in the same town (also home to NY Knife Co.) was in business until around 1920, when it was bought out by Winchester. At the time it was actually owned by E.C. Simmons Hardware (Keen Kutter).

It CAN be confusing!

Eric

The flyer from the Walden Knife auction 1928
http://www.collectors-of-schrades-r.us/ ... Walden.pdf

Those are some really nice knives everyone
Ive got one Walden Knife co i believe its a rattail pruner
Snaps like a beartrap and is a solid built knife

Travis,

Another nice old knife

Usually the springs on them old pruners are strong

very cool!!

Here's a little story to enlighten you about the shenanigans that went on in the knife shops. With the number of folks these places employed, you have to figure there was at least a little tomfoolery going on during the down times. This one involves the sometimes mascot of the old Walden Knife Co., a big 'ol tomcat named Oscar. Now the knife shop was located near the banks of the Wallkill River, and a small canal was run off the river to supply some water power for the equipment. One of the better known attributes of Oscar was his "ability" to drag folks across the canal in a one-on-one tug of war. How'd he do this you ask? Well it went something like this:

A new employee would eventually hear of Oscar's prowess, and be invited to test his mettle against the cat. A crowd would gather on either side of the canal, one to "tie" the rope around Oscar, the other to tie the rope around the participant. They'd each be situated on opposite banks at the water's edge, and while the folks on the employee's side kept his attention, someone would shout "GO!", and the Oscar side crowd would grab up the rope and drag the hapless victim across the canal before he knew what hit him. While he was spittin' and sputterin' on the bank, the crowd would make like they were untying the rope from around the cat, and console the stupified victim. Some folks would catch on right away, but there were a few who actually believed the cat had done it, including one person who actually demanded a re-match, insisting that he would beat that darned cat given a second chance.

Ahh, the good "ol days

Eric

Here is an old Walden doctor`s knife.

It has perfect Horn handles, worn blades, and grooved steel bolsters.

Here is a well used cattle knife with pickbone handles.

Nice knives fellas Bull

Miller Bro`s wrote:Here is an old Walden with most unusual aluminum bolsters nicely hand engraved.

One broken pen blade

I was just reading through this thread & thought I would show you my Walden. It's the same pattern as yours. I actually bought it as a gift, but then couldn't give it away once I got it.

I also found this write up in the Encyclopedia of Old Pocket Knives by Roy Erhardt. It appears to be out of the old Maher & Grosh catalog.

Kathy,

Very nice knife It is very similar to the one I posted a picture of. I like the way they drilled a hole in the center of each pin and then engraved the aluminum bolsters with the head of a flower

Burkinshaw and other early knife companies did this type of engraving on aluminum handle knives, and on just the bolsters. The most common engraved aluminum handle knives are the ones made for the E.H. Best Co. Boston Mass., most of these are made by Schrade, but you will find some by N.Y. Knife Co. and others.

I have this nice old Walden knife. On both tangs it I believe reads Walden Knife Co. Made in U.S.A. on the reverse side of the master blade is stamped on the tang 3864-1/4. I can not find out any info on this model! Is this a Muskrat or is this a Moose? It has nice stag bone handles and measures approx. 4" closed.

I just scored a 4039 bone handle. Soooooooooooooooo suhweeeeeet!

I'll post pics later (I'm posting in here so I can find this thread easily )

Okie dokie....here we go....

Walden Knife Co N.Y. 4" stockman sheepfoot and spay some blade loss to sharpening
master blade better, all in all a nice old knife.

Stockman

A Walden

I've noticed that most Walden knives are stamped "Walden Knife Co, New York", but I've seen several that were stamped "Walden Knife Co, Made in USA".

Does anyone know if the change in the tang stamp coincided with the takeover by Winchester, or if any Walden-stamped knives were made by Winchester in New Haven?

Yep, Id like to know the answer to that one too since my recent find is stamped "MADE IN USA" also. Hopefully we can get more info.

Bob

That's a beauty of a knife Bob

Nice one Bob!

Thanks for the kind words TJ and Dale,

I`m really hoping others will chime in on their finds and any detailed information on the Walden Knife Company and the knives they produced with pattern numbers, tang stamp variations, transition information to Winchester and to E.C. Simmons, etc. I`ve fallen in love with this knife and when I do this (as I have with others before )I kind of become a sponge on information about the maker.

Bob

I think, or at least I've read, that the "Made In U.S.A." tang stamps coincided with a Federal regulation passed in 1921.

Seems that's in Levine's Guide somewhere.

Charlie Noyes