3 3/4" KA-BAR jack
3 3/4" KA-BAR jack
Looking for a clip blade for a 3 3/4" KA-BAR, similar to case 31
I am the NRA.
Let's go Brandon!
Let's go Brandon!
Re: 3 3/4" KA-BAR jack
Do you know the model number Ken?
I have some Kabar blades that were from the era when they were made by Camillus, but I am not familiar with their pattern numbers.
Do you have a picture of the knife?
I have some Kabar blades that were from the era when they were made by Camillus, but I am not familiar with their pattern numbers.
Do you have a picture of the knife?
Dale
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
Re: 3 3/4" KA-BAR jack
Not sure of the model number but here's the sellers photo from when I bought the knife a few years ago.orvet wrote:Do you know the model number Ken?
I have some Kabar blades that were from the era when they were made by Camillus, but I am not familiar with their pattern numbers.
Do you have a picture of the knife?
The clip blade is pretty worn out on both ends. There's little to no snap due to worn shank.
edited warn to worn
I am the NRA.
Let's go Brandon!
Let's go Brandon!
Re: 3 3/4" KA-BAR jack
Ken,
I have a #1100 blade that might fit it, if your knife has a round end and not the square end tang.
The 1100 was a 3-7/8" stockman circa mid 1970s to mid 1990s. A guy may have to reprofiled the tip to get the blade to fit length wise.
I have a #1100 blade that might fit it, if your knife has a round end and not the square end tang.
The 1100 was a 3-7/8" stockman circa mid 1970s to mid 1990s. A guy may have to reprofiled the tip to get the blade to fit length wise.
Dale
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
Re: 3 3/4" KA-BAR jack
PM sent.orvet wrote:Ken,
I have a #1100 blade that might fit it, if your knife has a round end and not the square end tang.
The 1100 was a 3-7/8" stockman circa mid 1970s to mid 1990s. A guy may have to reprofiled the tip to get the blade to fit length wise.
I am the NRA.
Let's go Brandon!
Let's go Brandon!
Re: 3 3/4" KA-BAR jack
Ken,
Please resend the PM, for some reason I didn't get it.
-Dale
Please resend the PM, for some reason I didn't get it.
-Dale
Dale
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan
AAPK Administrator
Please visit my AAPK store: www.allaboutpocketknives.com/orvet
Job 13:15
"Buy more ammo!" - Johnnie Fain
“Evil is Powerless If The Good are Unafraid.” – Ronald Reagan