Turning Horn To Handles
- muskrat man
- Gold Tier
- Posts: 5667
- Joined: Fri Jun 30, 2006 4:04 am
- Location: Ohio
- Contact:
Turning Horn To Handles
I put this little tutorial together to show you how to process horns for use as knife handles. This applies for any American horned animal like cow and buffalo. Also, to avoid any confusion Elk, deer, and moose do not have horns, they have ANTLERS. Antlered animals shed their headgear, horned animals (with the exception of antelope) do not.
We start off with an ordinary cow horn
Mark it where it the tip starts getting solid
and cut it off
Now I make a rough mark and slice the horn in two. Always keep the cut parallel to the curve of the horn so if the horn is twisted you need to follow the curve of the horn, don't just make a straight cut or you'll lose material
Here it is sliced right down the middle
At about the halfway point is where the thickness begins to noticeably change, I'll get one thick set and one thinner set out of this relatively small horn plus I'll have the tip for another project.
Here is everything
decent thickness once you get in off the very edge
Chuck them all in boiling water, it doesn't stink too bad so you can do it inside if the wife will be gone for the day. I don't have that problem so I just boil them right in the kitchen. You could do it outside or in an outbuilding on a propane stove, turkey burner, ect. The hotplates I tried don't get hot enough to actually boil the water, the horn simmered for 5 hrs and was still too hard to clamp.
On a good rolling boil for around an hour for the thinner pieces, 1.5-2 hr for the thicker pieces ( 3/16" thick) to get them soft enough to clamp flat.
You can clamp them many ways but the best way I found by far was to use two flat pieces of wood (or metal, micarta ect as long as they're flat) and sandwich the horn between them and clamp them in a vice. This gives you the leverage and power you need to make the pieces good and flat.
You should leave them clamped for a few hours to ensure they are fully dry and cool so they do not return to their previous curved state after removing them from the clamps.Nevertheless they will still need surface sanding to make them flat enough to install on a pocket knife.
I will update this in a day or two with a photo of the completed product installed on a knife.
We start off with an ordinary cow horn
Mark it where it the tip starts getting solid
and cut it off
Now I make a rough mark and slice the horn in two. Always keep the cut parallel to the curve of the horn so if the horn is twisted you need to follow the curve of the horn, don't just make a straight cut or you'll lose material
Here it is sliced right down the middle
At about the halfway point is where the thickness begins to noticeably change, I'll get one thick set and one thinner set out of this relatively small horn plus I'll have the tip for another project.
Here is everything
decent thickness once you get in off the very edge
Chuck them all in boiling water, it doesn't stink too bad so you can do it inside if the wife will be gone for the day. I don't have that problem so I just boil them right in the kitchen. You could do it outside or in an outbuilding on a propane stove, turkey burner, ect. The hotplates I tried don't get hot enough to actually boil the water, the horn simmered for 5 hrs and was still too hard to clamp.
On a good rolling boil for around an hour for the thinner pieces, 1.5-2 hr for the thicker pieces ( 3/16" thick) to get them soft enough to clamp flat.
You can clamp them many ways but the best way I found by far was to use two flat pieces of wood (or metal, micarta ect as long as they're flat) and sandwich the horn between them and clamp them in a vice. This gives you the leverage and power you need to make the pieces good and flat.
You should leave them clamped for a few hours to ensure they are fully dry and cool so they do not return to their previous curved state after removing them from the clamps.Nevertheless they will still need surface sanding to make them flat enough to install on a pocket knife.
I will update this in a day or two with a photo of the completed product installed on a knife.
Custom knives, repair, restoration & embellishment
Certified Hubertus, Taylor, & Schrade repairman past and present
http://www.muskratmanknives.com
https://www.facebook.com/Muskratmanknives
Certified Hubertus, Taylor, & Schrade repairman past and present
http://www.muskratmanknives.com
https://www.facebook.com/Muskratmanknives
Re: Turning Horn To Handles
This is pretty cool MM
"There are none so blind as those that refuse to see"
God Bless America - Though I don't know why he would want to.
God Bless America - Though I don't know why he would want to.
Re: Turning Horn To Handles
Great, MM!
A lot simpler than the other articles had implied.
(good to know this doesn't end in divorce... maybe just extra chores. )
........ Joe
A lot simpler than the other articles had implied.
(good to know this doesn't end in divorce... maybe just extra chores. )
........ Joe
I've got a camouflage knife, but I can't find it.......
..... cardboard addicted.....
"The old timer's concentrated on making knives; not keeping records!!" ~ Bonfire bob
..... cardboard addicted.....
"The old timer's concentrated on making knives; not keeping records!!" ~ Bonfire bob
- whitebuffalo58
- Posts: 2743
- Joined: Tue Aug 17, 2010 2:35 am
- Location: SW MO Heart of the Ozarks
Re: Turning Horn To Handles
Excellent tutorial, MM! Can't wait to see the knife. I'm gonna hafta try a couple myself now.
Thanks, WB
Thanks, WB
Re: Turning Horn To Handles
I was just thinking about how do this myself the other day
Thanks very much for the tutorial
Brett.
Thanks very much for the tutorial
Brett.
Brett.
West Aussie Case Collector.
West Aussie Case Collector.
- muskrat man
- Gold Tier
- Posts: 5667
- Joined: Fri Jun 30, 2006 4:04 am
- Location: Ohio
- Contact:
Re: Turning Horn To Handles
Just noticed my "day or two" was up so I cobbled together this Boker whittler real quick with the horn, once it gets thin it is translucent so it would be a good idea to give the backside a shot of white spray paint before gluing it up. That way you can't see to the liner once it's polished. Darker horn would not have this problem.
Custom knives, repair, restoration & embellishment
Certified Hubertus, Taylor, & Schrade repairman past and present
http://www.muskratmanknives.com
https://www.facebook.com/Muskratmanknives
Certified Hubertus, Taylor, & Schrade repairman past and present
http://www.muskratmanknives.com
https://www.facebook.com/Muskratmanknives
Re: Turning Horn To Handles
That old cow horn looks pretty nice
"There are none so blind as those that refuse to see"
God Bless America - Though I don't know why he would want to.
God Bless America - Though I don't know why he would want to.
- whitebuffalo58
- Posts: 2743
- Joined: Tue Aug 17, 2010 2:35 am
- Location: SW MO Heart of the Ozarks
Re: Turning Horn To Handles
Here's an old Kutmaster I did after reading the tutorial. It was a big help! Thanks again, Kaleb!
I kinda messed up, the colorful slab was supposed to end up on front!
WB
I kinda messed up, the colorful slab was supposed to end up on front!
WB